manuals/manuals_Support_Center_manuals_PM0597_05_Boardwalk_conversion

Hi Scores Menu ...................... p. 16

Clear High Scores ............ p. 16

Books Menu ............................ p. 17-18

Books Display .................... p. 17

Cash Settlement ................ p. 18

System Menu ............................ p. 19

Diagnostics Menu ..................... p. 20

My Operator Info ....................... p. 21

Promotion Menu ....................... p. 21

Promo Credits .................... p. 21

Merit Money ......................... p. 22

Ad Screen Menu ....................... p. 22

Operator Ad Screens .......... p. 22

Boardwalk Hardware

Megatouch Operator Keys ........ p. 23

Cloning Machine Settings ......... p. 24

DIP Switch Settings ................... p. 25

Troubleshooting ........................ p. 26-28

Software License Agreements p. 29-34

Conversion Instructions

Replacing the Control Panel .... p. 3

Installing the Unassembled
Control Panel Components ...... p. 3-4

Installing the Setup Button
and Meter .................................. p. 5

Installing the Dongle Socket .... p. 5

Coin and Bill Acceptor
Connections .............................. p. 5

Canadian Coin Mech
Installation ................................ p. 5

Wiring the Electronics Box ...... p. 5-9

Installing the Signs & Decals ... p. 10

Final Steps ................................ p. 1

Boardwalk Software

Main Menu ............................... p. 12-13

Credits/Pricing Menu .............. p. 14

Quick Price Setup ............. p. 14

Coin-In Menu .................... p. 15

Games Menu ........................... p. 15-16

Game Setup ..................... p. 15-16

Table of Contents

Merit Boardwalk, MegaNet

and

TournaMAXX

are registered trademarks of Merit Entertainment.

Reproduction of this manual, in any form or by any means, is strictly forbidden without the written permission of Merit
Entertainment.

This kit will directly convert IT Golden Tee 2000-2004 and Global VR games and

may also convert other cabinets.

NOTE:

In order to perform this conversion, the monitor in your game must meet

the following requirements: The monitor must be an SVGA (800 x 600 resolution)

monitor with the ability to switch between 800 x 600 and 640 x 480 resolution and

it must have a 15-pin high-density DB connector. If the monitor in your game does

not meet the specifications, you must replace the monitor. Merit has two sources

that sell these compatible monitors for your convenience:

Wells-Gardner Model #: WGM2794-U0TS09R (IT Golden Tee Games only)

Wells-Gardner Model #: WGM2794-U0TS40E (Global VR Games only)

Wells-Gardner phone: 800-336-6630

Kortek Model #: KT-2914F-IT (IT Golden Tee Games only)

Kortek Model #: KT-2914F-VR (Global VR Games only)

Distributor: Casinotech phone: 702-736-8472

Merit Boardwalk Conversion Instructions

1 MERIT BOARDWALK CONVERSION PM0597-05

The Merit Boardwalk™ Conversion Kit is solely developed by Merit Entertain-
ment® and is not sold in connection with or sponsored by any other compa-
nies.

CONTENTS:

PM0597-05 MERIT BOARDWALK CONVERSION 2

QTY

PART NUMBER

DESCRIPTION

SA0590-05

ELECTRONICS BOX

MW1279-01

ELECTRONICS BOX MOUNTING BRACKETS

LB1150

12 V COIN DOOR BULB

SB0470-02

DONGLE SOCKET ASSEMBLY

SA4090

SETUP BUTTON AND BRACKET

SA0309-04

METER ASSEMBLY

HW5993-01

NYLON HEX STANDOFF

HW4487

#10 x 5/8L” PAN HEAD PHILLIPS SHEET METAL SCREWS

HW4201

#6 - 32 x 1/4L” PAN HEAD PHILLIPS SEMS SCREWS

HW3255

#10-32 KEPNUTS

HW5250

3/64” T x 7/32” ID x ½” OD, #10 FLAT WASHERS

HW0098-02

#6 x 3/8” L PAN HEAD PHILLIPS THREAD-FORMING SCREW

EC0174-02

TRACKBALL CABLE

EC0176-01

POWER CORD

SA0600-01

BILL ACCEPTOR HARNESS (Global VR Games)

SA0601-01

BILL ACCEPTOR HARNESS (Golden Tee Games)

EC2001

POWER CABLE

EC0195-01

MONITOR AC JUMPER HARNESS

EC2179-01

CENTRONICS CABLE

PM9998-01

SERIAL NUMBER LABEL

GL0065-02

MONITOR DURATRANS

GL0065-01

OVERHEAD DURATRANS

GL0062-04

SIDE DECALS

PM6064-06

BILL ACCEPTOR DECAL

PM6070-02

PLAYER KEY DONGLE DECAL

PM6003-01

MERIT ENTERTAINMENT LOGO DECAL

SA3509-01

OPERATOR KEY

HW8852

.38D,.20 HARNESS CLAMP

HW8854

.63D,.20 HARNESS CLAMP

HW9252-03

SELF-ADHESIVE VELCRO

HW8811

TIE WRAP

1
1

1
1
5
1
1
1

SA0595-01
GL0070-XX

-OR-

SW1001-03
MW1294-01
SW3044-XX
GL0064-03
PM6005-02
GL0069-XX

ASSEMBLED CONTROL PANEL
INSTRUCTION DECAL

-OR-

TRACKBALL
TRACKBALL MOUNTING PLATE
BUTTONS
CONTROL PANEL OVERLAY
TRACKBALL AND BUTTONS DECALS
BOARDWALK DECAL & INSTRUCTION DECAL

3 MERIT BOARDWALK CONVERSION PM0597-05

CAUTION:

Before performing any upgrade, it is important to remove any static electricity

from your body. To remove static electricity from your body, ground yourself by touching a
grounded piece of metal on the game before handling any boards, chips, connectors, etc.
Failure to ground yourself before performing an upgrade may result in damage to your
system and may prevent you from performing the upgrade.

NOTE: THIS INSTALLATION SHOULD ONLY BE PERFORMED BY A
QUALIFIED SERVICE TECHNICIAN.

Replacing the Control Panel

NOTE:

If you are reusing the control panel

in your game, skip to

Installing the

Unassembled Control Panel Compo-

nents

Turn off the game and disconnect it

from its power source.

Release the latches securing the con-

trol panel and tilt the panel open.

Disconnect the harness(es) from the

trackball and disconnect the fast-on

connectors from the buttons. Discon-

nect any other connections to the con-

trol panel, including the stop chain, if

applicable.

Remove the hardware securing the

control panel to the game and remove

the panel from the game.

Install the provided control panel with

the screws that secured the old panel

but do not fully tighten the screws.

Close the control panel and ensure that

it lines up correctly with the game. Make

any necessary adjustments, then,

completely tighten the screws. Remove

the protective plastic from the control

panel.

If you disconnected a stop chain, re-

connect it to the new control panel.

Continue with

Installing the Setup

Button and Meter.

Installing the Unassembled
Control Panel Components

Turn off the game and disconnect it

from its power source.

Release the latches securing the con-

trol panel and tilt the panel open.

10. Disconnect the trackball harness and

disconnect the fast-on connectors from

the buttons.

11. Remove buttons from the control panel

by unscrewing the nut on the under-

side of the panel and sliding the button

out of the top of the panel. See Figure

12. Remove the hardware securing the

trackball to the control panel and re-

move the trackball.

13. If applicable, remove the hardware that

secures the plastic overlay to the con-

trol panel and remove the overlay.

14. If applicable, remove the existing decal

from the panel and remove any remain-

ing adhesive residue with an adhesive

remover. When you are finished re-

moving excess adhesive from the

game, wipe the surfaces with alcohol

solvent. The surfaces must be clean

and free from dirt for the new decal to

adhere properly.

Before beginning this conversion, remove the existing electronics from the cabinet, leaving

only the existing A/C, speakers and speaker cabling, coin mechs, bill acceptor and ground

cables in the cabinet.

15. A trackball mounting plate is included if

you want to replace the existing plate.

To install the plate, remove the hard-

ware securing the old plate and remove

the plate. Then, install the new plate

with the hardware that secured the old

plate.

16. Peel the backing from the provided con-

trol panel overlay, line up the bottom of

the overlay with the bottom of the panel

and center the decal on the panel.

Gently adhere the overlay, making sure

to smooth out the surface from the cen-

ter to the edges. Then, carefully re-

move the protective plastic from the

control panel.

17. Cut the excess from the edges of the

overlay using an utility knife. Then, us-

ing the holes in the underside of the

control panel as a template, mark and

cut the holes for the buttons. Also, cut

out the hole for the trackball.

FIGURE 1 - CLOSE-UP OF BUTTON

COMMON TAB
(LABELED “COM 1”)

NORMALLY
OPEN TAB
(LABELED “NO 3”)

NORMALLY
CLOSED TAB
(LABELED “NC 2”)

NUT TO SECURE
BUTTON

18. Using Figure 2 as a guide for button

color, install the supplied buttons in the

control panel. To install the buttons,

unscrew the nut from the button, in-

sert the button through the mounting

hole in the control panel, and reinstall

the nut to secure the button in the panel

(see Figure 1).

NOTE:    If  the  buttons  on  the  right  side
of  your  control  panel  are  horizontally
oriented,  install  the  green  button  on
the  outside  and  the  red  button  on  the

inside.

19. Place the new trackball assembly over

the captive studs on the mounting plate.

NOTE: The controller is marked with
an arrow and "MONITOR" notation to

assist with proper positioning.

20. Use the nuts that secured the old

trackball to secure the trackball to the

captive studs. Make sure not to over-

tighten the nuts, as this can cause the

trackball to warp.

21. Adhere the rest of the decals onto the

control panel. Refer to Figure 2 for

placement of the decals.

PM0597-05 MERIT BOARDWALK CONVERSION 4

Coin & Bill Acceptor Connections

27. Unlock and open the coin and bill

door(s). Disconnect the existing fast-

on connectors going to the coin mech

and coin mech lightbulb, and, if appli-

cable, disconnect the connector to the

bill acceptor.

Installing the Setup Button and
Meter

22. Unlock and open the coin door. Re-

move the hardware securing the ex-

isting meter, disconnect the harness

from the meter and remove the old meter

and harnessing from the game.

23. Install the provided meter in the coin

mech area using the supplied Velcro.

24. Install the provided setup button and

bracket in the coin mech area using

the 2 provided #6 x 3/8" L pan head

Phillips thread-forming screws or the

provided Velcro.

Installing the Dongle Socket

See

Megatouch Operator Keys

for infor-

mation on dongle socket functionality.

25. Use the coin door to access the card

reader or blanking plate on the front of

the game. Remove the hardware se-

curing the reader or plate to the game,

disconnect any harnesses and remove

the card reader assembly or blanking

plate from the game.

26. Install the provided dongle socket as-

sembly in the opening. Secure the

ground wire to one of the threaded

studs on the plate and secure the as-

sembly to the game using the #10-32

kepnuts and washers.

5 MERIT BOARDWALK CONVERSION PM0597-05

28. Remove the existing 2 coin door

lightbulbs and replace them with the

provided bulbs. If you are installing the

Canadian coin mech, only install one

lightbulb on the same side that you will

be installing the supplied coin mech.

29.

Golden Tee Games Only:

Connect the

9-pin connector on the supplied bill ac-

ceptor harness (SA0601) to the mat-

ing connector from the bill acceptor and

route the other end of the cable to-

wards the rear of the cabinet.

30.

Global VR Games Only:

Connect the

9-pin connector on the supplied bill ac-

ceptor harness (SA0600) to the mat-

ing connector from the bill acceptor. Se-

cure the ground wire to a ground near

the bill acceptor and route the other

end of the cable towards the rear of

the cabinet.

Canadian Coin Mech Installation

31. If your kit included a Canadian coin

mech, remove the hardware securing

the existing coin mech and remove the

mech. Locate the EC0104 harness, with

the 10-pin connector on the end, com-

ing from the electronics box. Route the

free end of this harness towards the

coin door and connect it to the supplied

coin mech. Then, install and secure

the coin mech in the same fashion the

old coin mech was secured.

Wiring the Electronics Box

32. Unlock and open the rear door of the

cabinet. Place the provided electron-

ics box near the rear of the cabinet in

order to connect the harnesses.

PM0597-05 MERIT BOARDWALK CONVERSION 6

36. Locate the EC0173 harness coming

from the electronics box. Route the

free end of this harness towards the

coin mech and connect the fast-on

connectors to the tabs on the coin mech

lightbulbs.

37. Locate the EC0111 harness coming from

the electronics box. Route the free end

of this harness towards the meter in

the coin mech area and connect it to

the harness attached to the meter in

the coin box area.

38. Locate the EC0175 harness coming

from the electronics box. Route the

free end of the harness up to the con-

trol panel. Using Figure 2 as a guide,

connect the fast-on connectors on the

harness to the normally open tabs (re-

fer to Figure 1) on the buttons.

33. Locate the EC0190 harness, with the

2-pin connector on the end, coming

from the electronics box. Route the

harness towards the setup button in

the coin mech area and connect it to

the harness from the setup button.

34. Locate the EC0165 harness, with the

2-pin connector on the end, coming

from the electronics box. Route the

harness towards the coin mech area

and connect it to the harness from the

dongle socket.

35. Non-Canadian Games Only: Locate the

EC0170 harness, with the 4 fast-on

connectors on the end, coming from

the electronics box. Route the free end

of this harness towards the coin mech

and connect the fast-on connectors on

the end of the harness to the tabs on

the coin mechs. The green wire will

get connected to the common tab and

the white wire will get connected to
the normally open tab on the coin mech.

NOTE:    With  both  coin  mechs  wired,
there  is  a  chance  that  if  a  customer
drops  2  coins  simultaneously,  that  both
coins  will  not  register.

FIGURE 2 - CONTROL PANEL LAYOUT

WHITE BUTTON -

CONNECT HARNESS

LABELED #1

RED BUTTON -

CONNECT HARNESS

LABELED #4

YELLOW

BUTTON -
CONNECT

HARNESS

LABELED #3

GREEN BUTTON -

CONNECT HARNESS

LABELED #5

WHITE BUTTON -

CONNECT HARNESS

LABELED #2

INSTRUCTION

DECAL

CENTRONICS

CONNECTOR

HARD DRIVE

CONTROL BOARD

(SECURITY KEY,

SETUP BUTTON

LOCATION)

POWER

INLET

(not shown)

DETAIL VIEW OF

CONNECTOR SIDE VIEW OF MOTHERBOARD

AUDIO

VGA
VIDEO

ACCESS HOLE

FOR WIRE
ROUTING
(BOTH SIDES)

PARALLEL PORT

FOR TRACKBALL

FIGURE 3 - ELECTRONICS BOX

7 MERIT BOARDWALK CONVERSION PM0597-05

39. Locate the EC0185 harness coming

from the electronics box. Route the

free end of the harness up to the con-

trol panel and connect the fast-on con-

nectors on the harness to the common

tabs (refer to Figure 1) on the buttons.

This harness provides ground for the

buttons, so the wires can be connected

to any button.

40. Connect the provided EC0174 harness

to the parallel port on the motherboard

(see Figure 3) and secure the connec-

tor to the board using the two provided

nylon standoffs. Then, connect the 4-

pin power connector on the same har-

ness to a mating free 4-pin connector

coming from the electronics box. Route

the free end of the harness up to the

control panel and connect it to the

trackball harness.

41. Secure the ground wires from the

trackball using the existing nuts. Make

sure the ground is connected to earth

ground.

42.

Golden Tee Games Only:

Locate the

3-pin connector on the end of the

EC0186 coming from the electronics

box. Connect the free end of this har-

ness to the mating connector on the

existing harness coming from the

speakers. Secure the ground wire on

the harness to the grounding stud by

the power inlet with a nut.

PM0597-05 MERIT BOARDWALK CONVERSION 8

43.

Global VR Games Only:

Disconnect

the audio connector from the

motherboard in the electronics box (see

the connector side view in Figure 3).

Disconnect the existing audio cable

from the computer in the rear of the

cabinet and plug it into the audio port

on the motherboard in the electronics

box (see Figure 3).

44.

Global VR Games Only:

Leave the

monitor power connector connected to

the power strip inside the cabinet. Dis-

connect the VGA connector from the

computer inside the cabinet and plug it

into the VGA connector on the

motherboard in the electronics box (see

Figure 3).

45. If you have replaced the monitor in your

game, an AC jumper harness has been

provided in this kit to supply AC to the

monitor (EC0195). Connect the power

cord from the monitor to mating con-

nector on this harness and connect the

other end to the existing AC. Then,

connect the VGA connector from the

monitor to the VGA connector on the

motherboard in the electronics box (see

Figure 3).

46.

Global VR Games Only:

Connect the

provided power cord to the power in-

let on the electronics box (see Figure

3). Connect the other end of the power

cord to the power strip in the bottom of

the game.

47.

Golden Tee Games Only:

Connect the

mating connector on the harness al-

ready connected to the bill acceptor

(SA0601) to the mating connector on

the provided power cable (EC0176).

Connect the other end of the power

cable to the power inlet on the elec-

tronics box (see Figure 3). Connect

the other end of the bill acceptor har-

ness to a mating 3-pin connector al-

ready inside the game on the electron-

ics shelf (black, green and white

wires). Connect the 2-pin connector

to the SA0599 coming from the elec-

tronics box.

48.

Global VR Games Only:

Connect the

2-pin connector on the harness already

connected to the bill acceptor (SA0600)

to the 2-pin connector on the harness

labeled SA0599 coming from the elec-

tronics box. Plug the other end of the

harness into the power strip in the bot-

tom of the game.

49. Carefully lay the electronics box in the

rear of the cabinet with the fans facing

up. Secure the box to the cabinet floor

using the two supplied L brackets, two

#6 x 1/4”L and two #10 x 5/8”L screws

as shown in Figure 4.

Installing the Signs & Decals

50. Remove the existing decals (remove

any remaining adhesive residue with

an adhesive remover).

51. When you are finished removing any

excess adhesive from the game, wipe

the surfaces with alcohol solvent. The

surfaces must be clean and free from

dirt for the new decals to adhere prop-

erly.

52. Remove the hardware securing the top

marquee holder and remove the mar-

quee holder (see Figure 5).

53. The provided top marquee must be cut

to fit your game. Use the blue arrows

as a guide to cut the marquee to fit

Global VR games, use the green ar-

rows for Golden Tee games.

54.

Golden Tee Games Only:

Fold the top

LED display marquee back so that it is

not visible from the front of the game.

55. Replace the old marquee with the pro-

vided marquee. Resecure the marquee

holder with the same 3 screws.

56. Remove the screws securing the sign

over the monitor (see Figure 6). Re-

move the existing sign and replace it

with the provided sign. Secure the new

sign with the same screws.

57. If your bill acceptor accepts $1, $2, and

$5 dollar bills, adhere the bill acceptor

decal (reading “Insert bill here”) below

the bill acceptor as shown in Figure 6.

58. Adhere the provided “instructions” de-

cal to the panel as shown in Figure 2.

59. Finally, adhere the player key dongle

decal directly above the dongle socket

assembly on the front of the game.

FIGURE 5 - CONVERTED CABINET

TOP
MARQUEE

SIGN OVER
MONITOR

“INSERT
BILL HERE”
DECAL

SIDE DECAL

(BOTH SIDES)

PM0597-05 MERIT BOARDWALK CONVERSION 10

Final Steps

60. Plug in and turn the game back on and

allow the software to boot up.

61. Make sure that the picture is centered

on the screen. Make any necessary

adjustments using the existing monitor

control board attached to the monitor in

the rear of the cabinet.

NOTE:  BE  EXTREMELY  CAREFUL  TO
AVOID  THE  FLYBACK  TRANSFORMER
AND  HIGH  VOLTAGE  WIRE  RUNNING

TO THE MONITOR.

62. To ensure proper operation of the coin

and bill acceptors, drop coins into the

game and make sure they register cor-

rectly. Also check to make sure that

the meter changes when the coins are

dropped. If the coin or bill acceptors

are not operating properly, refer to

Coin-In Menu

in the software manual.

This will allow you to manually set the

coin values.

63. It is very important that you install the

serial number label (PM09998-01) on

the game. This serial number must be

provided for service or parts replace-

ment. It will also be required for parts

warranty. Locate the old game serial

number tag on the back of the game

and adhere the new tag next to it.

64. Press the

SETUP

button located in the

coin box area of the game to access

the Operator Setup Menu.

65. Roll the trackball to the

Diagnostics

button, then touch the yellow (C) but-

ton to enter the menu. Complete the

video test, and I/O test to verify proper

upgrade installation. The I/O test

screen allows you to check that all

buttons are functioning properly, to

make sure the meter is incrementing

properly, and to test the coin/bill func-

tionality. After finishing the diagnos-

tics tests, exit out of the setup screens

and verify audio output and gameplay.

66. Use the provided tie wraps and cable

clamps to properly dress the wires in

the rear of the cabinet. Be careful not

to crush any wires when replacing the

rear door. Close and lock the rear door.

11 MERIT BOARDWALK CONVERSION PM0597-05

Main Menu

The Main Menu can be accessed by pressing the SETUP button inside the game. Use the

Main Menu to set up all game software options. Use the trackball to move between selec-

tions. Current selections will be highlighted. Press the C button to select.

NOTE: For help with the Options in any menu section (“?” icon appears), press

the HELP button to bring up a help screen.

A summary of the Main Menu functions appears in the following table. For more detail, see

the corresponding sections of the manual.

FIGURE 1 - MAIN MENU

Main Menu

Available Options

Information

CREDITS/
PRICING

Quick Price Setup

Coin-In

Value of Credit

Options

Clear/Free Credits

The Credits Screens allow the operator
to set credit rules for all games, set up
the Coin-In Menu, and add or clear
credits.

GAMES

Game Setup

Options

In the Games Screens, you can edit the
game list (choose which games are
available) and select options for
individual games.

HI SCORES

Clear High Scores

Options

Select

Clear All Games

to clear all high

scores or choose a particular game to
clear high scores for that game

BOOKS

Books Display

Cash Settlement
Setup

Cash Settlement
Collection

Use the Books Screens to gather
current and lifetime credits information,
review and calculate location and
operator fees, and see revenue details.

SYSTEM

Set Time

Security Setup

Display Serial No.

Volume Control

Set 6 Star PIN

Data Transfer

Options

Setup Operator
Keys

Recharge Key

Set the game clock, security PIN, game
volume, 6 star PIN (default is

4123

) and

features. Also set system options such
as language control and 6 Star Enable.
Use this menu to transfer books data or
clone machine settings with a USB pen,
set up Operator Keys, or utilize
Recharge Keys.

PM0597-05 MERIT BOARDWALK CONVERSION 12

Main Menu

Available Options

Information

DIAGNOSTICS

Video Test

I/O Test

View System Log

Checksum Test

System Info

Trackball Test

Enters the Video Test to display the
test screens. Press any button to cycle
through the test.

Tests the function of the I/O board, DIP
switches, coin meter, and lockout (if
applicable).

Displays operations performed by the
game.

Checks the hard drive for missing or
corrupted files.

Gives details about various hardware
components in the game.

Tests trackball operation. Follow the
instructions on the screen.

MY OPERATOR
INFO

Add/Edit Operator

Information

Allows operator to enter/edit name, Web
address, description, and phone number,
which can be viewed by the player when
selecting “Help” from the main player
menu.

PROMOTION

Options

Promo Credits

Merit Money

Enables Merit Money, and Promo
Credits features.

Sets time periods in which the game
offers free credits while in Idle Mode.

Sets time periods in which location
owners can use the 6 Stars feature to
offer free credits to encourage game
play.

AD SCREEN

Operator Ad Screens

Allows the operator to create ad screens
and add custom screens created on a
personal computer.

13 MERIT BOARDWALK CONVERSION PM0597-05

Credits/Pricing Menu

Quick Price Setup -

This feature is only available on U.S. games.

Quick Price Setup allows the operator to make general pricing changes without entering the
Games Menu.

FIGURE 2 - QUICK PRICE SETUP SCREEN

4 Credits for a Dollar (default setting)

: Sets each game to the following price settings:

NOTE: If the game is set to 3 Credits for a Dollar, prices will only display as credits.

3 Credits for a Dollar

: Sets each game to the following price settings:

C O IN IN P U T

C O IN V AL U E

C O IN S

CR E D ITS

M ET ER PU L SE S

1 A

25 ¢

2 B

25 ¢

5 E

$ 5.00

COIN INPUT

COIN VALUE

COINS

CREDITS

METER PULSES

25¢

$5.00

PM0597-05 MERIT BOARDWALK CONVERSION 14

Games Menu

Game Setup

The game list and prices, as well as game

options, are programmed using these

screens. The Game Setup Screen shows

the game menu positions available, with the

list at the bottom showing all available games.

FIGURE 4 - GAMES MENU: GAME SETUP

To Enter This Screen, Select “Game

Setup” on the Games Menu

The Game Setup Screen also allows you to

make these general changes:

Default Games

: Resets the selected cat-

egory menu to its default game and price

settings.

Clear One

: Clears a selected item from the

player’s game menu.

Clear All

: Clears all games from the player’s

game menu.

Enable All Games

: Turns on all games

within the selected category and defaults

the price settings.

Coin-In Menu

FIGURE 3 - COIN-IN MENU

Game cost can be controlled two ways: by

changing the number of credits required to

play a game or by changing the cost of a

credit. The Coin-In Menu allows you to ad-

just the cost of a credit, as well as provide a

way to give players “bonus” credits for de-

positing a higher amount of money. Use the

left and right arrows to change the number

of credits.

When programming the Coin-In Menu, Chan-

nel 1 is set for the lowest value coin, Chan-

nel 2 for the next highest value, etc. Meter

pulses are independent of credits and only

track the unit of currency. Players can be

given an incentive to deposit more money

by giving them “bonus” credits for deposit-

ing larger denominations. Coins may be de-

posited in any combination of values and

the game will automatically register the high-

est number of credits for the total amount of

coins deposited. Once a game is played,

any remaining fractional credits are erased.

Generally, most countries have a factory

default setting. This setting can be adjusted

(as described above), but will return if the

game memory is cleared. Some programs,

depending on the key used, have a currency

default display located to the left of the coin

inputs. It shows the currency value for each

of the coin inputs. This display is used as a

guide and is not used in any calculations.

Select the currency default display to hide/

show the display.

To give customers bonus credits for insert-

ing a five-dollar bill, enter the Coin-In Menu

and adjust the number of credits in the $5.00

row.

15 MERIT BOARDWALK CONVERSION PM0597-05

To customize the available games, first se-

lect

Clear

All

to clear the game list. Choose

the menu position you want a particular game

to occupy by rolling the trackball to that po-

sition, then select the desired game name

from the game list on the bottom of the

screen. Repeat until all desired games ap-

pear in the menu (a game cannot appear in

the list more than once). Games already in

the menu will be red in the game list at the

bottom of the screen.

To adjust the price, use the trackball and C

button to select and change the credit value

next to each game.

Some games support a cost to continue func-

tion. Games that support continuation will

show a credit value in the cost to continue

column; games that do not support this func-

tion will display N/A. The cost to continue is

adjustable on a game-by-game basis. Se-

lect the credit value button to change the

amount.

NOTE:    The  default  Cost  to  Continue
price  is  the  same  as  the  default  cost  to
play  the  game;  however,  the  Cost  to
Continue  does  not  need  to  be  the  same
amount  as  the  original  price.

Hi Scores Menu

Clear High Scores

Use this menu to manage high scores. Clear

all scores for all games by selecting

Clear

All Games

. To clear the high scores for an

individual game, select that game and choose

YES

when prompted.

FIGURE 5 - HI SCORES MENU:

CLEAR HIGH SCORES SCREEN

To Enter This Screen, Select

“Clear High Scores” on the

Hi Scores Menu

PM0597-05 MERIT BOARDWALK CONVERSION 16

Select the

“+”

next to each game to display

the current and lifetime credit totals, divided

into 1-4 player totals, and linked game totals.

It also shows the shortest, average and long-

est playing times for that game.

Books Display also shows coin input data,

as well as Promotional Credits and Merit

Money (when these features are enabled).

Select the

“+”

next to Total Coins to display

individual coin input statistics.

NOTE:    Books  data  can  be  exported  to
a  file  USB  pen  via  the  System  Menu/
Data  Transfer/Export  Books  feature.
The .data file can then be viewed with a
word  processing  program  after  con-
necting  the  storage  device  to  a  per-
sonal  computer.    The  file  will  display
basic game information such as the soft-
ware  version,  the  game  serial  number,
and  date/time  information  relating  to
books  data.    The  file  will  also  show  the
current  and  lifetime  credit  totals,  as
well  as  credit  totals  for  each  game  fea-
tured  on  the  machine.

FIGURE 7 - BOOKS MENU:

BOOKS DISPLAY SCREEN WITH

GAME SELECTED

To Enter This Screen, Select “Books

Display” on the Books Menu and

Choose a Game Name

Books Menu

The Books Screens display the current and

lifetime credit totals for each game, as well

as the percentage of credits played per game

(the percentage for each game is the total

number of credits played on that game di-

vided by the total number of credits entered

into the machine).

Books Display

FIGURE 6 - BOOKS MENU:

BOOKS DISPLAY SCREEN

The books information can be sorted in three

ways with the button that toggles through

the sorting categories.

Unsorted

displays

the books information in the standard order.

Sorted by Current

displays the current

credits for each game from most to least

played.

Sorted by Lifetime

displays the

lifetime credits for each game beginning with

the most played game.

Select

Clear Current

to erase all current

books data. The date the data was last

cleared will appear at the top of the Books

Screen.

To Enter This Screen, Select “Books

Display” on the Books Menu

17 MERIT BOARDWALK CONVERSION PM0597-05

Cash Settlement Setup

The Cash Settlement Screens are used to

calculate the percentage of earnings the op-

erator and location will receive, as well as

any fees collected by the operator. The first

screens allow you to set up the Cash Settle-

ment Screen. Choose YES or NO to display

the operator’s cut on the Cash Settlement

Collection Screen and enter the percentage

of revenue the location will receive. Also,

select the fee calculation method. Select

per month if you do not make regular weekly

collections or per week if you collect every

7 days. Then select NEXT.

To Enter This Screen, Select “Cash

Settlement Setup” on the Books

Menu and select “NEXT”

FIGURE 8 - BOOKS MENU:

CASH SETTLEMENT SETUP SCREEN

NOTE:    Monthly  fee  collections  are
based on 4.3 week  month.  If you change
your  fee  calculation  method,  the  game
will  auto  adjust  the  fees  by  multiplying
or  dividing  by  4.3  and  rounding  to  the
nearest  penny.

NOTE:    Make  sure  the  time  and  date
are  set  on  the  game  in  order  to  ensure
correct  fee  calculation.

The next screen allows you to set up the

fees. The amounts can be changed on

screen by selecting the amount itself and

using the trackball to enter a dollar figure.

The other two columns display the cumula-

tive totals for each fee and the totals for the

FIGURE 9 - BOOKS MENU:

CASH SETTLEMENT SETUP SCREEN

FIGURE 10 - BOOKS MENU:

CASH SETTLEMENT COLLECTION

To Enter This Screen, Select

“Cash Settlement Collection” on the

Books Menu

Cash Settlement Collection

The Cash Settlement Collection Screens will

display the balance (total revenue minus to-

tal fees) to be split between the operator

and the location.

Select

Revenue Details/Cash Out

Fee

Details

for breakdowns and

Clear/Com-

plete Collection

to finish. Cash Settle-

ment totals will reset once collection is com-

plete.

current collection period. Fees are calcu-

lated on a prorated, per-day basis.

Select the NEXT button to display more

groups of fees. After setting up the fees,

select FINISH to save your changes.

PM0597-05 MERIT BOARDWALK CONVERSION 18

System Menu

FIGURE 11 - SYSTEM MENU

Set Time

The Set Time Menu allows you to set both the time and date on the
game. Time is shown in 24-hour, “military” time (e.g. 5:00pm =
17:00). Use the trackball and C button to set the time and date.

Security Setup

The operator can set the PIN number and select which of the
features (Coin-In, Free Credits, Game Menu, Hi Scores Menu,
Books Menu, All Options, My Operator Info, and Set 6 Star PIN) will
be protected by the PIN. To change the PIN, you must first enter
the existing PIN (the default PIN is

0000

), then enter a new 4-digit

number and touch

SET

on the keypad. The game will prompt you

to re-enter your PIN to confirm. After confirming your PIN, touch
the button for each of the features you wish to protect with the PIN.

Display Serial

Number

Use this screen to view the game’s serial number using the keypad.

Volume Control

Use the trackball to adjust the volume up or down. The on-screen
volume control can also be accessed using 6 Stars.

Set 6 Star PIN

(only appears if

PIN is enabled)

Brings up the Set 6 Star PIN Screen via the Options button on the
Player Menu. Set the 6 Star PIN (between one and six digits) using
this screen. You can enable this feature and choose which options
will be accessible by 6 Stars using the System Menu: Options
Screen. Select an option box under System Menu: Options for on-
screen help.

Data Transfer

Transfer information (Books data, ad screens) or clone machine
configuration using a USB Pen.

Options

For help with the Options in any menu section, select the option
and press HELP to bring up a help screen.

Setup Operator

Keys

Set/erase operator key data.

Recharge Key

Not Applicable.

19 MERIT BOARDWALK CONVERSION PM0597-05

Diagnostics Menu

FIGURE 12 - DIAGNOSTICS MENU

Video Test

Use the buttons to cycle through a series of video test screens.

I/O Test

Tests the control panel buttons, the control board’s SETUP and
CALIBRATE buttons, all coin channels, the coin meter, and the coin
lockout feature (if applicable). A green light next to the appropriate
button will register each time that item is tested, and the number next to
the item should increment by one with each test (

NOTE:

The

CALIBRATE button on the control board is represented by “Test” on the
Diagnostics screen, as it functions to test the trackball). The I/O Test
Screen also displays which DIP switches are on or off.

View System
Log

Displays a log of all operations performed by the game since the log
was last cleared. This information is helpful for customer service in
troubleshooting your game.

Checksum Test

Checks the hard drive for missing or corrupted files. With STOP ON
ERROR? set to YES, a message indicating which file is corrupted will
be shown whenever the game encounters an error. With STOP ON
ERROR? set to NO, a list of corrupted files will be displayed when the
test is complete. If errors are detected, the software on the drive may
need to be reloaded. If this does not solve the problem, the drive may
require replacement. The test could take up to 30 minutes.

System Info

Gives details about the following:

processor type and speed

motherboard manufacturer

amount of memory

network card info

sound chip type

video chip type

hard drive manufacturer and capacity

modem part identification number

fan speed

status

PSOC version

Trackball Test

Follow the on-screen instructions to test the trackball.

PM0597-05 MERIT BOARDWALK CONVERSION 20

My Operator Info

The My Operator Info Menu allows opera-

tors to add their contact information, which

can be viewed by players when the HELP

button is selected on the main player menu.

Operators can add their name, Web ad-

dress, description and phone number.

FIGURE 13 - MY OPERATOR INFO SCREEN

Promotion Menu

The Promotion Menu is designed to encour-

age player interest. Use the Options but-

ton to enable each feature.

FIGURE 14 - PROMOTION MENU

Promo Credits

NOTE: This feature is only available
in Amusement mode.

FIGURE 15 - PROMO CREDITS SCREEN

The Promo Credits feature generates inter-

est by offering operator-controlled free

credits while the game is in idle mode. Se-

lect days of the week, time frames, idle

time (number of minutes the game would

be in idle mode before free credits are of-

fered) and the number of credits (1-10) to

be awarded. A message announcing that

free credits are available will appear on

the screen during idle mode when Promo

Credits go into effect. Promo Credits ex-

pire after 10 minutes or when the Promo

Credits time period comes to an end.

21 MERIT BOARDWALK CONVERSION PM0597-05

Merit Money

NOTE: This feature is only available

in Amusement mode.

The Merit Money screens allow location

owners to encourage game play by offer-

ing free games (not free credits) at certain

time intervals via the 6 Stars feature. Se-

lect days of the week, time frames, and the

number of free games (1-10 per day) to be

awarded, as well as a PIN number for lo-

cation owners to use in order to access

Merit Money using the 6 Stars feature. Lo-

cation owners can enable Merit Money by

entering that specific PIN in the 6 Stars

screen. One free game is given away each

time the location enters the code until the

predetermined daily limit is reached. Free

games expire after 10 minutes, when money

is deposited into the machine, or when the

Merit Money time period comes to an end.

Ad Screen Menu

The Ad Screen Menu allows operators to

create ad screens and add custom screens

created on a personal computer.

FIGURE 16 - AD SCREEN MENU

Operator Ad Screens

A total of 24 advertising screens can be

created with the software and added to the

game. The ads will appear along with the

other attract screens when the game is in

idle mode. Custom images for ad screens

can also be added to the game using an

appropriate storage device for your game

(CD/DVD drive or a USB pen). Select the

green

“?”

buttons on each screen for in-

formation on how to create ad screens and

add custom screens to the machine.

In addition, a program for adding up to 120

additional ad screens can be downloaded

from our Web site (www.meritind.com) in

the Support/Software Downloads section.

PM0597-05 MERIT BOARDWALK CONVERSION 22

Megatouch Operator Keys

The Merit Boardwalk game uses operator keys to make it easy for operators to enter setup

to service machines. The keys are activated by touching them to the dongle socket on the

front of the game.

Operator Keys

Operator Keys can be programmed to make

it possible to access the Main Menu Screen

without opening the game. Operator keys

(with black handles) are provided with your

game. Additional Operator Key Kits (part

number KAV-111-002-01) can be purchased

from an authorized Merit distributor.

To program an Operator Key:

Press the SETUP button to enter the

Main Menu Screen.

Select the

System

button and then se-

lect

Setup Operator Keys.

Select the

Set Key

button. The game

will prompt you to touch a key to the

dongle socket on the game.

Touch the key to the socket and select

When prompted, remove the key and

select

The game will prompt you to enter a PIN

for the key. Enter a PIN and select

Set

New PIN

NOTE:

The PIN for each operator key

can  be  set  to  the  same  number,  if  de-
sired.    Additionally,  one  key  can  be
used  for  any  number  of  games.

Repeat these steps for each Operator Key.

Once the key is programmed, simply touch a

programmed key to the dongle socket and

enter your PIN when prompted. The Main

Menu Screen will then display.

Up to 4 different Operator Keys can be pro-

grammed on one game. To clear a pro-

grammed key, enter setup, touch

System

and then touch

Setup Operator Keys

Touch the key to the dongle socket, then

press the

Erase Key

button.

23 MERIT BOARDWALK CONVERSION PM0597-05

Cloning Machine Configuration

The USB pen allows operators to save the

machine configuration of one Boardwalk

game and import the configuration to an-

other game.

The configuration includes all the machine

options, the Coin-In table, credit value, game

pricing, game active/inactive data, volume

adjustment, operator key data, the 6 Star

PIN, My Operator Info data, Promo Credits

and Merit Money setup data, and the cur-

rent language setting.

A USB Pen is available as a separate kit

(part number KAV-100-008-01) from your

local distributor.

NOTE:  Cloning  the  machine  configu-
ration  will  overwrite  any  existing  con-
figuration  settings  saved  to  your  USB
pen.

Export Settings:

Remove the USB pen cap.

Unlock and open the control panel to

access the electronics box and

motherboard. It is not necessary to

open the box to access the USB port.

Plug the USB pen into one of the open

USB ports found on the connector side

of the motherboard (see Figure 20).

The LED on the pen will flash when the

device is first connected, then pulse

slowly after the initial connection.

If the game has not been turned on yet,

turn it on and let it finish booting up.

Press the SETUP button inside the ma-

chine.

Choose the

System

option on the Main

Menu.

Select

Data Transfer

on the System

Menu. If the pen was properly con-

nected, the game will display a mes-

sage indicating that a storage device

has been detected.

NOTE: If the NO STORAGE DEVICE
DETECTED appears, the USB pen was

not correctly connected to the machine.

Choose the

Export Machine Configu-

ration

option to transfer configuration

data to the pen. The machine will dis-

play a message when the data has

been successfully exported and the pen

can safely be removed.

Import Settings:

Repeat the preceding Steps 1-7 on the

Boardwalk game to which you would

like to import your copied configuration.

10. On the Data Transfer screen, choose

the

Import Machine Settings

option.

11. When the import is complete, a mes-

sage will appear informing the opera-

tor that the data transfer was success-

ful and that the software will restart to

allow the new configuration to take ef-

fect.

12. Select

. The machine will display a

message stating that the USB pen can

be disconnected.

NOTE: Only disconnect the pen after
the LED has returned to the slow pulse,

NOT while it is flashing.

PM0597-05 MERIT BOARDWALK CONVERSION 24

DIP SWITCH SETTINGS

The following table provides information on the functionality of the hard DIP switches in
the game. Make sure to read the information in the

Notes

column to determine what is

affected  when  performing  these  functions.    After  performing  any  DIP  switch  function,
make sure to follow the instructions on the screen.  In most cases, you will be instructed
to reset the DIP switch in order to reboot the game.  If you fail to reset the DIP switch before
rebooting, it could result in corruption of the hard drive.

NOTE:

The DIP switch functionality is built into the software. To access the DIP switches

through the software: Turn off the game. Set DIP switch 1 to the closed position. Turn
power on. When the message

Please reset DIP 1 to proceed

appears, reset DIP 1 to

the open position. The Merit diagnostics page will appear. Touch

for information on DIP

switch functionality. Touch the specific DIP switch to activate it. Touch

to exit.

DIP#

Function

Usage/Notes

Motherboard
configuration &
checksum test

Configures the CMOS settings on the motherboard to Merit
specifications and checks the files on the hard drive.

A checksum test should be performed when the game is locking
up or rebooting.  If the test fails, the program should be reloaded
onto  the  hard  drive.   After reloading, perform  another checksum
test.  If it fails again, the hard drive should be replaced.

Hardware
configuration

Identifies system hardware and configures the motherboard.

A hardware configuration occasionally needs to be performed
after a kit is installed and the touchscreen is not responding to
touch or the calibration is off.

5 & 7

Memory clear for
TournaMAXX™
and
TouchTunes®

Clears the login name, password, access phone number, and
all call-in settings for TournaMAXX users.

Clears all the loaded albums for TouchTunes users.

Clears current books, coin-in, high scores and resets the
software options.

A memory clear should be performed when a game is not able to
connect  to  TournaMAXX  and  there  is  some  question  about  the
information  in  the  Dial-Up  Network  Screen  being  correct.    After
performing a memory clear, TournaMAXX setup information must
be  re-entered,  and  an

Update From Server

should be

performed.

NOTE:

TournaMAXX games must perform

an Update From

Server

BEFORE performing a memory clear.

4 & 7

Complete
memory clear

Clears ALL memory on  hard  drive  including the TournaMAXX
player  database,  TournaMAXX  settings,  advertising  screens,
bookkeeping,  high  scores,  coin-in,  options,  etc.    It  resets  the
game to the factory defaults. It also marks bad sectors on hard
drive.

A  complete  memory  clear  should  only  be  performed  when  the
game is locking up or resetting and it has passed the checksum
test.    After  performing  a  memory  clear,  the  player  database
should be reloaded, TournaMAXX setup  information must be re-
entered, and an

Update From Server

should be performed.

NOTE:

TournaMAXX games must perform an

Update From

Server

BEFORE performing a complete memory clear.

Watchdog Timer

When the watchdog timer is enabled, it will reboot the machine
within 2 minutes of a failure, allowing the game to
automatically reset itself if a problem arises.

25 MERIT BOARDWALK CONVERSION PM0597-05

Merit Entertainment

Troubleshooting Guide for

Merit Boardwalk™ Games

ROBLEM

ORRECTIVE

CTION

no power

bill acceptor
motor does not
run

no flash on the
monitor screen

no cooling fans
operating

no output from
power supply

Check that the power cord is connected to a “live” outlet.

Check that the power switch is on.

Check that the power cord is connected to the game power supply.

Check that the power supply’s voltage select switch is set to the
proper voltage.

Check the harness connections to the on/off switch and circuit
breaker.

Check the circuit breaker for an “open”.

Check the A/C harness connection to the power supply.

Check the line cord.

no video

no cooling fan
operation

screen is blank

A/C power to the
monitor and bill
acceptor

no output from
power supply

Check the power on jumper wire located on the motherboard. It
should connect J2 to pin 21 of Panel 1. If this jumper wire is missing
or not connected between the correct pins, it may prevent the power
supply from turning on. For more information, see Tech Note 52.

Check the D/C harness connection to the motherboard.

Check the A/C harness connection to the power supply.

no video

cooling fans are
working

there is a sound
when coins are
deposited

Check the video cable connections to the motherboard and the
monitor.

Check the AC power harness to the monitor.

no video

constant beeping
or a sequence of
beeps

The memory card (DIMM) may not be seated properly. Reseat the
DIMM or replace it.

no video

no sound when
coins are
deposited

Check all connections to the motherboard.

Reseat the DIMM.

Replace the motherboard or send it for repair.

poor picture
quality

Adjust Brightness, Contrast, Horizontal, and Vertical controls with
monitor controls.

coin jam

Check the coin mech and coin chute for coins blocking the pathway.

Make sure the coin harness is connected between the normally
open and common terminals on the coin switch.

Disconnect the bill acceptor and the coin switch one at a time to
narrow down the problem.

Check the coin harness for pinched or damaged wires.

Disconnect the coin harness from J1, J3, J7, and J8 of the I/O
board. If the coin jam still appears, the I/O board will have to be sent
for repair.

meter not
advancing

Check connection at I/O board.

Check wiring at

J2 METER

connector on I/O board.

trackball not
working

Perform a DIP switch 8. Refer to the “DIP SWITCH SETTINGS”
section of the manual.

PM0597-05 MERIT BOARDWALK CONVERSION 26

Merit Entertainment

Troubleshooting Guide for

Merit Boardwalk

™

Games

continued

ROBLEM

ORRECTIVE

CTION

game locks up or
resets while
being played or
in the attract
mode

no movement on
the screen

power has to be
cycled off and on
to get the game
to function again

Check the output voltages from the power supply:

Enhance SFX 1211J

Red wire   +5 volt
Yellow wire +12 volt
Blue wire  -12 volt
White wire  +5 volt power good
Violet wire  +5 volt VSB
Black wire  ground
Brown wire +3.3 volt

Clean the vents and the fans of any dust and dirt that may interfere
with airflow.

Clean the CPU cooling fan on the motherboard.

Replace the CPU cooling fan if it is not operating properly.

Reseat the DIMM on the motherboard.

Clear memory with the following procedure:

Turn off the game.

Press and hold the

Setup

and

Calibrate

buttons.

Turn the game on and keep holding the buttons until the
screen displays “TWO BUTTON CLEAR DETECTED
RELEASE BUTTONS”. This should take about 30 seconds.

Release the buttons. This will clear high scores, clear the
books and reset options, and reset the game menu and coin
menu to their factory settings.

Perform a checksum test on the hard drive:

Turn off the game.

Turn on DIP switch 8 on the I/O board.

Turn on the game. The test will take about 10 minutes.

A failure will cause the test to stop.

A passed test will display “DRIVE CHECKSUM
COMPLETE RESET ALL DIP SWITCHES TO REBOOT
MACHINE”.

With power on, turn off DIP switch 8.

game locks up
with “invalid key
for version
PG3002 – V
XXXX”

Check the program number on the security key. It should be
compatible with the program on the hard drive.

Check the contacts on the security key socket. Lift up on the contact
on the bottom of the socket and make sure there is a good
connection to the base of the security key.

Check the USB cable that connects the I/O board to the
motherboard.

Try another security key with the same program number or test the
security key in another game with the same program version.

“INVALID KEY”
message while
downloading
software to the
hard drive

If the security key was replaced before the download:

The motherboard did not boot from the DVD drive.

Check that the DVD drive is set as master.

Check the ribbon cable connections between the DVD drive and the
motherboard.

Try another DVD drive or another set of discs.

27 MERIT BOARDWALK CONVERSION PM0597-05

Merit Entertainment

Troubleshooting Guide for

Merit Boardwalk

™

Games

continued

ROBLEM

ORRECTIVE

CTION

game will not
download disc

Make sure the disc is installed correctly, with the logo facing up.

Check for scratches or a defective disc.

Try a different DVD drive or another disc.

If you’re downloading a disc set, make sure each disc is of the same
revision.

"ERROR
READING DRIVE
C"

This message can be caused by the hard drive or in some
program versions, a coin jam while the game is turned on.

Turn the game off.

Locate DS 1, position 8 and turn it on.

Turn on power to the cabinet. This will start the
hard drive checksum test, which should take about
20 minutes to complete.

When the hard drive passes the test it will display
a "CHECKSUM GOOD" message and continue to
boot up into the game attract screens. This
indicates a coin jam.

When the hard drive fails the test, the game will
lock up with a "CHECKSUM ERROR" message,
which will stay on the screen until the power is
turned off. In this case, the hard drive will have to
be replaced.

"DISK BOOT
FAILURE"

This message indicates the motherboard is not receiving data from the
hard drive and has locked up.

Check the IDE ribbon cable connections to the motherboard and
hard drive.

Check the power to the hard drive. It should have +5 volts, +12
volts, and ground.

“QUANTUM
FIREBALL,
SMART FAILURE
DETECTED,
BACK UP HARD
DRIVE”

The self-diagnostics on the hard drive has detected an error.

The hard drive will have to be replaced.

“CRITICAL
ERROR ABORT
RETRY FAIL” or
“BAD COMMAND
OR FILE NAME”
error

Try reloading the program onto the hard drive with a different set of
update CD’s compatible with the security key. If it will not accept the
download, try another CD-ROM drive. If it still does not work,
replace the hard drive.

PM0597-05 MERIT BOARDWALK CONVERSION 28

Merit Industries, Inc. Software License Agreement

Merit Industries, Inc. (“Licensor”) is willing to license the enclosed software to you only if
you accept all of the terms in this license agreement (“Agreement”).

Ownership of the Software

The enclosed Merit® product, which may include but is not limited to the Megatouch®
software program (“Software”) and the accompanying written materials are owned
by Licensor and are protected by United States copyright laws, patent laws and
other intellectual property laws, by laws of other nations, and by international treaties.

Restrictions on Use and Transfer

If  this  Software  package  contains  multiple  media  types  (such  as  CD’s,  flash  cards,
hard  drives,  etc),  then  you  may  use  only  the  type  of  media  appropriate  for  your
Machine. You may not use the other media types on another Machine, or transfer, or
assign them to another user except as part of the permanent transfer of the Software
and  all  written  materials  (as  provided  for  below  in  paragraph  4).

You  may  make  one  copy  of  the  software  for  backup  purposes  only.    You  may  not
copy  or  make  backup  copies  of  any  software  security  key  or  software  security
device  under  any  circumstances.

You  may  permanently  transfer  the  right  to  use  the  Software  and  accompanying
written materials (including the most recent update and all prior versions) if you retain
no  copies  and  the  transferee  agrees  in  writing  to  be  bound  by  the  terms  of  this
Agreement.  Such  a  transfer  of  this  license  to  another  party  immediately  terminates
your license. You may not otherwise transfer or assign the right to use the Software,
except  as  stated  in  this  paragraph.

You  may  not  operate  or  allow  the  operation  of  the  Software  at  locations  where  the
operation  of  such  Software  does  not  comply  with  all  local,  state,  and  other
governmental body laws and regulations.  You agree to not use or permit the use of
the  Software  in  violation  of  any  U.S.  Federal,  state,  or  local  laws  or  regulations  or
any foreign law or regulation, including laws regarding gaming, gambling or intellectual
property  rights  in  or  concerning  the  Software.

You may not modify, adapt, translate, reverse engineer, decompile, disassemble the
Software or create derivative works from the Software or any component thereof;
nor may you remove, modify or hide or otherwise make unreadable or non-viewable
any notice, legend, advice, watermark or other designation contained on the Software,
component thereof, or output therefrom.

You agree that the Software and the authorship, systems, ideas, inventions methods
of operation, documentation and other information contained therein, and all versions,
modifications and adaptations thereto are proprietary intellectual properties of Licensor
and are protected by civil and criminal law, and by copyright, trade secret, trademark
and the patent laws of the United States and other countries.

Limited Warranty

Licensor warrants, solely for your benefit, that the Software will function in material
conformity, with its accompanying documentation for a period outlined in Licensor’s
standard product warranty period after your receipt of the Software.

Licensor’s Obligations Under Warranty

Licensor’s sole obligation under the aforesaid warranty shall be to utilize commercially
reasonable efforts to correct or modify such portion of the Software as to make it
materially conform with the applicable documentation.

29 MERIT BOARDWALK CONVERSION PM0597-05

Grant Of License

10. Licensor grants to you a limited, non-exclusive license to distribute and/or use one

copy of the Software on a single Merit (“Machine”) accompanied by a single licensor
factory authorized security key. Licensor reserves the right to update versions of the
software  and  the  content  to  the  Machine  as  deemed  appropriate  by  the  Licensor.
You  are  entrusted  to  maintain  and  protect  your  single  licensor  factory  authorized
security key, password, or other identification from being utilized by any third party,
and  you  agree  to  be  responsible  for  any  use  of  the  Software  provided  herein  by  a
third  party  utilizing  your  identification.    Licensor  maintains  the  right  to  immediately
terminate  your  License  for  reasons  related  to  misuse  or  other  non-conformity  with
the  rules  expressed  herein.    While  Licensor  does  not  routinely  inspect  Machines,
Licensor also reserves the right to inspect or audit the Software from time to time in
Licensor’s  sole  discretion.    To  the  extent  that  Licensor’s  access  to  the  Software
requires  that  Licensor  also  gain  access  to  a  Machine  in  which  the  Software  is
installed,  you  agree  to  promptly  provide  Licensor,  when  requested,  with  permission
and aid in Licensor gaining access to the Machine.

Disclaimers

11. EXCEPT AS PROVIDED IN THE SECTION ENTITLED “LIMITED WARRANTY”, LICENSOR

MAKES NO OTHER PROMISES, REPRESENTATIONS OR WARRANTIES, WHETHER
EXPRESSED OR IMPLIED, REGARDING OR RELATING TO THE SOFTWARE OR
CONTENT THEREIN OR TO ANY OTHER MATERIAL FURNISHED OR PROVIDED TO
YOU PURSUANT TO THIS AGREEMENT OR OTHERWISE AND LICENSOR SPECIFICALLY
DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO SAID MATERIALS OR THE USE THEREOF.
TO THE MAXIMUM EXTENT ALLOWABLE BY LAW THE UNIFORM COMMERCIAL CODE
OR OTHER UNIFORM LAWS SHALL NOT APPLY TO THIS AGREEMENT.

Limitation on Liability

12. IN NO EVENT SHALL LICENSOR BE LIABLE UNDER ANY CLAIM, DEMAND OR ACTION

ARISING OUT OF OR RELATING TO THE SOFTWARE, ITS USE, INSTALLATION OR
LICENSOR’S PERFORMANCE OR LACK THEREOF UNDER THIS AGREEMENT FOR
ANY SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES,
WHETHER OR NOT LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
CLAIM, DEMAND OR ACTION. IN ADDITION, WITHOUT LIMITING THE FOREGOING, IN
ALL EVENTS THE REMEDIES AVAILABLE TO YOU SHALL BE LIMITED TO THE AMOUNT
PAID BY YOU TO LICENSOR FOR THE SOFTWARE.

13. IN NO EVENT WILL LICENSOR BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

LOSS OF PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF YOUR USE, MISUSE, BREACH OF THIS AGREEMENT OR
INABILITY TO USE THE SOFTWARE.

General

14. The validity and construction of this Agreement and of the rights and obligations herein

shall be determined and governed by the laws of the State of New York.  By accepting
the  terms  of  this Agreement,  you  acknowledge  and  accept  that  the  courts  of  New
York,  New York  shall  have  exclusive  jurisdiction  and  venue  regarding  any  disputes
arising  with  regard  to  this  Agreement  or  arising  out  of  activity  or  misuse  of  the
Software.

15. Merit, in its sole discretion, may assign this agreement or any of its rights and

obligations hereunder.

16. If you have any questions concerning this Agreement or wish to contact Licensor for

any reason, please write: Merit Industries, Inc., 2525 State Road, Bensalem, PA
19020, USA.

PM0597-05 MERIT BOARDWALK CONVERSION 30

Contrat de licence de logiciel de Merit Industries, Inc.

Merit Industries, Inc. (ci-après le "Concédant") est disposé à vous accorder la licence d'utilisation
du logiciel ci-inclus, à condition que vous vous engagiez à respecter tous les termes, clauses et
conditions du présent contrat de licence (Contrat).

Droit de Propriété
1.

Le produit Merit ci-joint contenant, mais ne s'y limitant pas, le logiciel Megatouch™ (ci-après le
"logiciel") et toute la documentation écrite, restent la propriété du Concédant et sont protégés
par : les lois de droits d'auteur des Etats-Unis, les lois s'appliquant aux brevets déposés et à
la propriété intellectuelle, ainsi que par celles des autres pays et les traités internationaux.

Restriction d'Utilisation et Transfert
2.

Si le présent logiciel comprend plusieurs types de composants (tels que CD-ROM, cartes
flash, disques durs, etc), vous ne pouvez utilisez que ceux qui conviennent à votre appareil.
Il est strictement interdit de les utiliser sur un autre appareil, les transférer -ou les céder à un
autre utilisateur, sauf en cas de transfert permanent du logiciel et de toute la documentation
écrite (comme indiqué ci-dessous au paragraphe 4).

Il est interdit de copier le logiciel, à l'exception d'une copie de sauvegarde. Il est aussi interdit
de reproduire -ou faire des copies de sauvegarde des programmes de clé de sécurité ou
autres fichiers de sécurité, quelles que soient les circonstances.

Vous  pouvez  céder  en  permanence  à  un  tiers  -le  droit  d'utiliser  le  LOGICIEL  et  toute  la
documentation écrite l'accompagnant, (ainsi que la plus récente mise à jour et toutes autres
anciennes  versions)  seulement  si  vous  n'en  gardez  aucune  copie,  et  si  le  cessionnaire
s'engage, par écrit, à respecter les termes, clauses et conditions du présent Contrat. Cette
cession  à  un  tiers  met  fin  à  votre  licence  immédiatement. Autrement,  vous  n'avez  pas  la
permission de transférer ou d'accorder à un tiers le droit d'utiliser le présent logiciel, excepté
que tel que décrit dans le présent paragraphe.

Il est interdit d'utiliser le présent logiciel ou de permettre son utilisation dans des emplacements
où  l'utilisation  du  présent  logiciel  n'est  pas  conforme  aux  lois  et  réglementations  locales,
nationales ou réglementations d'autres organismes gouvernementaux.  Vous acceptez de ne
pas utiliser ou d'autoriser l'utilisation du logiciel d'une manière enfreignant les lois ou regula-
tions s'appliquant à la propriété intellectuelle et au jeu, en vigueur aux Etats-Unis ou dans les
autres pays du monde, y compris les lois  de l'ensemble du logiciel.

Il est interdit de modifier, adapter, traduire, démonter, décompiler, désassembler le logiciel ou
créer du matériel dérivé du logiciel ou de tout composant de celui-ci ; vous ne pouvez pas
enlever, modifier ou cacher ou rendre illisible ou non-visible toute instruction, légende, infor-
mation ou filigrane ou autre désignation qui apparaît dans le logiciel, composant dudit logiciel
ou résultant dudit logiciel.

Vous convenez que le logiciel et les droits d'auteur, les systèmes, les idées, les inventions, les
méthodes d'utilisation, la documentation et autre information incluse, ainsi que toutes les
versions, modifications et adaptations qui s'y rattachent sont les propriétés intellectuelles du
Concédant et sont protégées par le droit civil et pénal et par le droit d'auteur, le secret
commercial, la marque déposée et le brevet aux Etats-Unis et dans les autres pays du monde.

Limite de Garantie
8.

Le Concédant garantit seulement à votre intention, que le logiciel permettra une utilisation
conforme, avec la documentation l'accompagnant, pendant la période de temps indiquée
dans la période de garantie du produit standard du Concédant, à compter de la date de
livraison du logiciel.

Responsabilité du Concédant aux termes de la Garantie
9.

La seule obligation du Concédant aux termes de la garantie susmentionnée sera de faire tous
les efforts commercialement raisonnables pour corriger ou modifier la partie du logiciel pour
le rendre matériellement conforme aux spécifications de la documentation.

31 MERIT BOARDWALK CONVERSION PM0597-05

Concession de Licence
10. Le Concédant vous accorde le droit d'utiliser une seule copie par appareil Merit (ci-après

"Appareil")  accompagné  d'une  seule  clé  de  sécurité  autorisée  en  usine  et  fournie  par  le
Concédant. Le Concédant se réserve le droit de mise à jour des versions du logiciel et du
contenu  de  l'Appareil,  quand  il  juge  nécessaire  de  le  faire.      Il  vous  appartient  également
d'empêcher que les mots de passe ou autres codes et la clé de sécurité soient utilisés par un
tiers. Vous acceptez d'assumer la responsabilité dans le cas de l'utilisation du logiciel par un
tiers.  Le Concédant se réserve le droit de résilier votre contrat de licence à tout moment dans
l'éventualité d'une utilisation non-conforme aux clauses stipulées.  Bien que le Concédant ne
contrôle pas les appareils périodiquement, il se réserve toutefois le droit de contrôler le logiciel
à tout moment et sans préavis de sa part.  De surcroît, dans l'éventualité où le logiciel n'est
accessible qu'à travers la machine dans laquelle il est installé, le licencié s'engage à donner
libre accès au Concédant, ou ses représentants, à la machine et dans les plus brefs délais.

Exclusion de toute autre garantie
11. EXCEPTE COMME PREVU DANS LA SECTION INTITULEE "LIMITE DE GARANTIE", LE CONCEDANT

N'ASSURE AUCUNE AUTRE GARANTIE DE QUELQUE NATURE ET A QUELQUE TITRE QUE CE
SOIT, EXPLICITE OU IMPLICITE, EN RAPPORT AVEC LE LOGICIEL ET LES COMPOSANTS QUI
L'ACCOMPAGNENT OU, LE CAS ECHEANT, TOUT SUPPORT OU MATERIEL FOURNI
CONFORMEMENT AU PRESENT CONTRATEN PARTICULIER, LE CONCEDANT NE PEUT
DONNER AUCUNE GARANTIE, DE QUELQUE NATURE QUE CE SOIT, POUR LA
COMMERCIALISATION DE TOUS LES PRODUITS EN RAPPORT AVEC LE LOGICIEL OU AVEC
L'UTILISATION DE CELUI-CI. DANS LA MESURE OU CELA EST PERMIS PAR LA LOI, LE CODE
UNIFORME COMMERCIAL OU AUTRE LOI UNIFORME NE S'APPLIQUE PAS AU PRESENT
CONTRAT.

Limite de Responsabilité
12. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DE TOUTE RECLAMATION,

DEMANDE OU ACTION RESULTANT DE OU EN RAPPORT AVEC LE LOGICIEL, SON UTILISATION
OU SON INSTALLATION, OU LA PERFORMANCE OU MANQUE DE PERFORMANCE DU
CONCEDANT EN VERTU DU PRESENT CONTRAT POUR TOUS DOMMAGES D'UNE NATURE
QUI N'EST PAS PRESUMEE PAR LA LOI ET QUI DOIVENT ETRE EXPRESSEMENT PROUVES,
DOMMAGE INDIRECTS, DOMMAGES-INTERETS POUR PREJUDICE MORAL, QUE LE
CONCEDANT AIT ETE AVISE OU NON DE LA POSSIBILITE D'UNE TELLE RECLAMATION,
DEMANDE OU ACTION. DE PLUS, SANS LIMITER CE QUI PRECEDE, LES DEDOMMAGEMENTS
A VOTRE DISPOSITION SERONT LIMITES AU MONTANT QUE VOUS AUREZ PAYE AU
CONCEDANT POUR LE LOGICIEL.

13. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSIBLE : D'UNE RUPTURE DE CONTRAT,

DES DOMMAGES, Y COMPRIS TOUTE PERTE DE PROFIT, PERTES D'ECONOMIE OU TOUS
AUTRES DOMMAGES INDIRECTS OU DOMMAGES-INTERETS ACCESSOIRES DECOULANT
DE LA MAUVAISE UTILISATION OU DE L'IMPOSSIBILITE D'UTILISATION DU LOGICIEL.

Dispositions Générales
14. La validité et la construction du présent Contrat et les droits et obligations ci-inclus seront

déterminés et régis par les lois de l'état de New York aux États-Unis. En acceptant les
dispositions du présent contrat, vous acceptez également que tous litiges ou revendications
relatives seront réglés par voie d'arbitrage par un tribunal de l'état de New York, aux Etats-
Unis.

15. Merit Industries se réserve le droit de transférer le présent Contrat à un tiers ainsi que ses

droits et obligations ci-après.

16. Pour toutes questions concernant le présent Contrat -ou si vous désirez contacter le Concédant

pour une raison quelconque, veuillez écrire à : Merit Industries, Inc., 2525 State Road, Bensalem,
PA 19020, Etats-Unis.

PM0597-05 MERIT BOARDWALK CONVERSION 32

Merit Industries, Inc. Softwarelizenzabkommen

Merit Industries, Inc. („Lizenzgeber”) ist nur dann bereit Ihnen eine Lizenz für die

beiliegende Software zu erteilen, wenn Sie alle Bestimmungen dieses Lizenzabkommens
(“Abkommen”) akzeptieren.

Eigentumsvorbehalt der Software
1.

Das beiliegende Merit®-Produkt, welches das Megatouch® Softwareprogramm („Soft-
ware”) beinhalten kann, aber nicht darauf beschränkt ist, und die schriftlichen Unterlagen
sind Eigentum des Lizenzgebers und sind durch die Gesetze der Vereinigten Staaten
und anderer Länder und durch internationale Verträge urheberrechtlich geschützt.

Beschränkungen im Gebrauch und Transfer
2.

Sollte  diese  Softwarelieferung  mehrere  Medien  enthalten  (z.B.  CD,  Karten,  Festplatten
usw.), dürfen Sie nur die für Ihre Maschine angebrachte Medienart verwenden.  Die anderen
Medienarten  dürfen  nicht  auf  anderen  Maschinen  verwendet  werden  oder  an  Dritte
übergeben  werden,  abgesehen  von  einem  endgültigen  Transfer  der  Software  und  aller
schriftlichen Unterlagen (wie im untenstehenden Paragraphen 4 beschrieben).

Sie dürfen nur eine Sicherungskopie der Software herstellen. Unter keinen Umständen
dürfen Sie einen Softwaresicherungsschlüssel oder Sicherungsmaßnahmen kopieren oder
davon Sicherungskopien herstellen.

Sie dürfen das Nutzungsrecht für die Software und die schriftlichen Unterlagen (einschließlich
der aktuellen Version und aller vorhergehenden Versionen) an Dritte übertragen, wenn Sie
keine Kopie behalten und wenn der Empfänger die Bestimmungen dieses Abkommens in
schriftlicher Form akzeptiert.  Bei einem solchen Transfer der Lizenz an Dritte erlischt Ihre
Lizenz umgehend.  Abgesehen von den Bestimmungen dieses Paragraphen sind alle anderen
Transfers  oder  Übertragungen  der  Nutzungsrechte  für  diese  Software  unerlaubt.

Sie  dürfen  die  Software  nicht  benutzen  oder  eine  Nutzung  gestatten,  wenn  eine
solche  Nutzung  der  Software  irgendwelche  Gesetze  und  Verordnungen  der
kommunalen  oder  staatlichen  Behörden  verletzen  würde.  Sie  verpflichten  sich  die
Software nicht so zu nutzen oder nutzen zu lassen, dass sie damit gegen staatliche,
Bundes-  oder Lokalgesetze oder Bestimmungen der USA oder gegen  ausländische
Gesetze  oder  Bestimmungen,  einschliesslich  aller  Gesetze  bezüglich  Glücksspiels,
Spielens  oder  geistigen  Eigentumrechts  der  Software,  verstossen.

Es  ist  Ihnen  nicht  gestattet,  die  Software  abzuändern,  zu  verändern,  zu  übersetzen,
rückumzuwandeln, zu dekompilieren oder zu zerlegen, oder aus der Software oder eines
Teils davon andere Werke abzuleiten.  Sie dürfen auch aus der Software, einem Bestandteil
der Software oder aus den Datenausgaben der Software keine Hinweise, Bemerkungen,
Ratschläge,  Wasserzeichen  oder  andere  Markierungen  entfernen,  verändern,  verbergen
oder auf andere Art unlesbar machen.

Sie  akzeptieren,  dass  die  Software  und  die  Urheberschaft,  die  Systeme,  die  Ideen,
Erfindungen,  die Arbeitsweisen,  die  Dokumentation  und  alle  anderen  darin  enthaltenen
Informationen und alle Versionen, Veränderungen, und Bearbeitungen davon das geistige
Eigentum  des  Lizenzgebers  sind,  und  dass  sie  durch  Straf-  und  Zivilgesetzgebung  und
durch  die  Copyright-,  Geschäftsgeheimnis-,  Warenzeichen-  und  die  Patentgesetze  der
Vereinigten Staaten und anderer Länder geschützt sind.

Beschränkte Garantie
8.

Der Lizenzgeber garantiert zu Ihren Gunsten, dass die Software für die angegebene
normale Garantiezeit des Lizenzgebers nach Ihrer Annahme der Software in erheblicher
Übereinstimmung mit der beiliegenden Dokumentation laufen wird.

Verpflichtung des Lizenzgebers im Rahmen der Garantie
9.

Die ausschließliche Pflicht des Lizenzgebers im Rahmen der vorstehenden Garantie besteht
darin, alle geschäftlich vertretbaren Schritte zu unternehmen, um Teile der Software zu
berichtigen oder abzuändern, bis sie mit der beiliegenden Dokumentation erheblich
übereinstimmen.

33 MERIT BOARDWALK CONVERSION PM0597-05

Übertragung der Lizenz
10. Der Lizenzgeber gewährt Ihnen eine beschränkte, nicht-ausschliessbare Lizenz zur

Vertreibung und/oder Benutzung einer Kopie der Software auf einem einzelnen Merit™ („Gerät”)
mit einem einzelnen werksmäßig gestatteten Sicherungsschlüssel.  Der Lizenzgeber behält
sich das Recht vor, nach eigenem Ermessen die Software und den Inhalt der Maschine zu
verbessern. Sie sind dafür verantwortlich ihren  individuellen,  vom  Lizenzgeber werksmäßig
gestatteten Sicherheitsschlüssel, ihr Passwort oder anderweitigen Identifikationsmechanismus
instandzuhalten und abzusichern gegen die Nutzung durch eine dritte Partei, und sie akzeptieren
die Verantwortung für jegliche Nutzung der besagten Software durch eine dritte Partei mithilfe
ihresIdentifikationsmechanismus  .  Obwohl  der  Lizenzgeber  nicht  regelmässig  Maschinen
inspiziert, behält sich der Lizenzgeber das Recht vor, ihre Lizenz umgehend  zu kündigen aus
Gründen des Missbrauchs oder bei Nichtbefolgung der Bestimmungen in diesem  Vertrag. Der
Lizenzgeber behält sich ebenfalls das Recht vor, die Software  von Zeit zu Zeit nach eigenem
Ermessen zu inspizieren oder zu überprüfen. Im Falle, dass der Lizenzgeber Zugang zu dem
Gerät wünscht, in dem besagte Software installiert ist,  erklären Sie sich bereit, dass sie dem
Lizenzgeber, wenn nötig, Erlaubnis und Hilfe beim Zugang zum Gerät verschaffen.

Beschränkungen
11.

ABGESEHEN VON DEN BESTIMMUNGEN DES PARAGRAPHEN „BESCHRÄNKTE GARANTIE"
GIBT DER LIZENZGEBER KEINE SONSTIGEN VERSPRECHEN, VERPFLICHTUNGEN ODER
GARANTIEN, OB AUSDRÜCKLICH ODER STILLSCHWEIGEND, FÜR DIE SOFTWARE ODER
IHRE BESTANDTEILE ODER FÜR ALLE ANDEREN MATERIALIEN, DIE IHNEN IM RAHMEN DIESES
ABKOMMENS ZUR VERFÜGUNG GESTELLT ODER ÜBERLASSEN WERDEN, UND DER
LIZENZGEBER LEHNT AUSDRÜCKLICH ALLE ANSPRÜCHE AUF MARKTFÄHIGKEIT UND
EIGNUNG DER BESAGTEN MATERIALIEN FÜR DEN GEWÖHNLICHEN GEBRAUCH AB. SOWEIT
GESETZESMÄSSIG ZUGELASSEN, SOLLEN DIE HANDELSRECHTLICHE GESETZGEBUNG
AUS DEM UNIFORM COMMERCIAL CODE ODER ANDERE GESETZE AUF DIESES ABKOMMEN
NICHT ANWENDBAR SEIN.

Haftungsbeschränkung
12. DER LIZENZGEBER HAT KEINERLEI HAFTUNG BEI EINEM ANSPRUCH, EINER FORDERUNG

ODER EINER KLAGE, DIE AUF NUTZUNG DER SOFTWARE, DEREN INSTALLIERUNG, DER
LEISTUNG DES LIZENZGEBERS ODER DESSEN VERSAGEN IM RAHMEN DIESES ABKOMMENS
FÜR JEGLICHE FOLGE-, INDIREKTE, SONDER- ODER NEBENSCHÄDEN BERUHEN, SELBST
WENN DER LIZENZGEBER AUF DIE MÖGLICHKEIT EINES SOLCHEN ANSPRUCHES, EINER
FORDERUNG ODER EINER KLAGE HINGEWIESEN WURDE. WEITERHIN UND OHNE
BESCHRÄNKUNG DES LETZTEN SATZES, DÜRFEN IN ALLEN FÄLLEN DIE IHNEN ZUR
VERFÜGUNG STEHENDEN ABHILFEN DIE VON IHNEN FÜR DIE SOFTWARE AN DEN
LIZENZGEBER GEZAHLTE SUMME NICHT ÜBERSCHREITEN.

13. DER LIZENZGEBER HAT IN KEINEM FALL EINE HAFTUNG IHNEN GEGENÜBER FÜR SCHÄDEN,

EINSCHLIESSLICH ETWAIGER GEWINNVERLUSTE, NICHT REALISIERTER EINSPARUNGEN
ODER ANDERER NEBEN- ODER FOLGESCHÄDEN, DIE AUS IHRER VERWENDUNG,
MISSBRAUCH, VERLETZUNG DIESES ABKOMMENS ODER GEBRAUCHSUNFÄHIGKEIT DER
SOFTWARE ENTSTEHEN.

Allgemein
14. Die Rechtsgültigkeit und Provisionen dieses Abkommens und der darin enthaltenen Rechte und

Pflichten werden durch die Gesetze des Staates von New York bestimmt.  Sollten sie diese
Vereinbarungen  annehmen,  dann  akzeptieren  Sie,  dass  der  ausschliessliche  Erfüllungsort
und Gerichtsstand bei den Gerichten von New York im Staat New York liegen hinsichtlich aller
Streitigkeiten,  die  diesen  Vertrag  betreffen,  oder  die  durch  Leistung  oder  Missbrauch  der
besagten  Software  entstehen.

15. Merit kann nach eigenem Ermessen dieses Abkommen oder jedes der darin enthaltenen

Rechte und Pflichten an Dritte abtreten.

16. Bei Rückfragen über dieses Abkommen oder wenn Sie den Lizenzgeber aus einem anderen

Grund kontaktieren wollen, bitte schreiben an: Merit Industries, Inc., 2525 State Road, Bensalem,
PA 19020, USA.

PM0597-05 MERIT BOARDWALK CONVERSION 34

NOTES:

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________

___________________________________________________________________

__________________________________________________________________

___________________________________________________________________

__________________________________________________________________

________________________________________________________________

_________________________________________________________________